B A C K

PART 1 - GENERAL

1.1 SECTION INCLUDES

A. Floor anchored, overhead braced pilasters (Metropolitan style).

B. Floor anchored pilasters (New Yorker style).

C. Ceiling hung pilasters (Empire style).

D. Floor to ceiling pilasters (Gramercy style).

E. Urinal screens.

1.2 QUALITY ASSURANCE

A. Source: Provide partitions and screens which are the products of one manufacturer.

B. Coordination: Coordinate related work such as concealed blocking to ensure proper location and quantity.

1.3 SUBMITTALS

A. Product Data: Submit manufacturer’s product data, installation details, and catalog cuts for partitions, hardware and accessories.

B. Shop Drawings: Provide shop drawings for field measurements, fabrication, installation and erection of all parts of the work.

C. Manufacturer’s Installation Instructions: Provide details of hardware locations and drilling dimensions.

1.4 FIELD MEASUREMENTS

A. Verify that field measurements are as indicated on shop drawings. Advise manufacturer of any changes.

1.5 DELIVERY, STORAGE AND HANDLING

A. Deliver materials and products in unopened factory labeled packages. Store and handle in strict compliance with manufacturer’s instructions and recommendations. Protect from all possible damage. Inspect cartons at the time of delivery and advise carrier of any damage immediately.

1.6 MATERIAL

A. Panels, doors, pilasters, urinal screens and shoes to be made of #304 stainless steel with a #4 polish finish. All parts to be protected against scratching with a vinyl coating which is to be removed after installation.

PART 2 - PRODUCTS

2.01 ACCEPTABLE MANUFACTURERS

A. Knickerbocker Partition Corporation

2.02 MATERIALS AND PRODUCTS

A. Panels, Urinal Screens and Doors: Shall be 1” thick, constructed from two sheets of 20 gauge type #304 stainless steel with a #4 finish. Sheets to be formed and cemented under pressure to a structural vermin-proof honeycomb core. Formed sheets shall be welded together at intervals around entire perimeter to ensure a rigid one-piece integral unit. All edges shall be bound with a 20 gauge stainless steel interlocking molding and formed with stainless steel corner clips.

B. Metropolitan Pilasters: Shall be 1-1/4” thick, constructed of two sheets of 20 gauge type #304 stainless steel with #4 finish. Sheets to be formed and cemented under pressure to a structural vermin-proof honeycomb core. Formed sheets shall be welded together at intervals around entire perimeter to ensure a  rigid one-piece integral unit. All edges shall be bound with an 18 gauge stainless steel interlocking molding. Bottom of pilasters shall have adjustable floor anchor, with leveling device, anchor studs and locking nuts to firmly secure pilasters to floor. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.

C. Headrail: Partitions and pilasters, when set in place, shall be securely braced with 1” x 2” anodized aluminum anti-grip headrail bracing, inserted and securely fastened into the top of the pilasters with theft-resistant screws.

D. New Yorker Pilasters: Shall be 1-1/4” thick, constructed of two sheets of 18 gauge, type #304 stainless steel with #4 finish. Sheets to be formed and cemented under pressure to a vermin-proof honeycomb core. Formed sheets shall be  welded together at intervals around entire perimeter to ensure a rigid one-piece integral unit. All edges shall be bound with an 18 gauge interlocking molding and formed with stainless steel corner clips. Pilasters, when set in place, shall be securely anchored to concrete sub-floor by means of 3/8” diameter cadmium plated bolts with a minimum penetration of two inches, secured rigidly into concrete slab with expansion shields and secured to the pilasters through a one-piece 12 gauge channel integrally welded to the pilasters. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.

E. Empire Pilasters: Shall be 1-1/4” thick, constructed of two sheets of 18 gauge, type #304 stainless steel with #4 finish. Sheets to be formed and cemented under pressure to a vermin-proof honeycomb core. Formed sheets shall be welded together at intervals around entire perimeter to ensure a rigid one-piece integral unit. All edges shall be bound with an 18 gauge interlocking molding and formed with stainless steel corner clips. Pilasters, when set in place, shall be securely anchored to overhead carrying member (overhead structural steel members to be furnished, installed and drilled by others) by means of 3/8” diameter cadmium plated bolts through a one-piece 12 gauge channel integrally welded to the pilaster. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.

F. Gramercy Pilasters: Shall be 1-1/4” thick, constructed of two sheets of 20 gauge, type #304 stainless steel with #4 finish. Sheets to be formed and cemented under pressure to a vermin-proof honeycomb core. Formed sheets shall be welded together at intervals around entire perimeter to ensure a rigid one-piece integral unit. All edges shall be bound with an 18 gauge stainless steel interlocking molding. Both the top and the bottom of the pilasters shall have adjustable anchor and leveling devices. Anchor studs and locking nuts designed to firmly secure the pilaster to the floor and ceiling. Both assemblies to be concealed with 3” high stainless steel plinths, secured in place with concealed clips.

G. Hardware and Fittings: Panels and pilasters shall be attached to one another and/or to walls with Zamac chrome plated brackets. Doors shall be equipped with Knickerbocker Ever Life Spring Activated Non-Rising hinges. Top Hinge Pivot Door Bracket to be recessed and inset into edge of door, approximately 2” below the top with a pivot pin, operating on a self-lubricating bushing, mounted within the door structure, supported both above and below the pivot bracket. Operation of door shall be controlled by opposing cams under spring tension, mounted on a fixed vertical pintle. Hinges to be adjustable to permit door to rest at any angle, or to hold door open or closed when not latched. Hinges shall operate without raising or lowering the door on a fixed horizontal plane. Each door shall be equipped with stop and keeper, combination coat hook and bumper and concealed latch, featuring a latch cover which permits access to the compartment in case of emergency. Handicap door to be equipped with Knickerbocker Partition Corporation Lever Handle. Design to comply with ADA requirements. Hinge bracket and stops shall have clamp flanges to transmit the strain of door closing to the pilaster. All hardware shall be heavy one-piece, non-ferrous “Zamac” casting, heavily chrome plated. Hinges, stop and keeper, pilaster and panel brackets shall be thru-bolted with sex bolts having theft-resistant heads.

PART 3 - EXECUTION

3.01 INSTALLATION

A. Install partitions secure, rigid, plumb and level in accordance with manufacturer’s instructions.

B. Maintain manufacturer’s recommended spacing between wall and panels and between wall and pilasters.

C. Equip each door with hinges, concealed lock, coat hook and bumper, door strike and keeper. Outswing doors shall have a door pull and wall bumper.

3.02 ADJUSTMENT

A. Adjust operating parts to work easily, smoothly and correctly.

B. Adjust and align hardware to uniform clearance at vertical edge of doors, not  exceeding 3/16 inch.

C. Adjust hinges to position inswing doors at a 30 degree angle to pilasters and outswing doors to a fully closed position.